Search By Part Number	Straight Accessories 90° Accessories 45° Accessories Miscellaneous Accessories Support Data/ Assembly Procedures   Descriptions SE50 SE51 SE52 SE53 SE54 SE55 SE56 SE57 SE58 SE59 SE60 SE61 SE62 SE63 SE64 CLICK HERE TO VIEW A LARGER IMAGE EXAMPLE BASIC PART NUMBER click here for SERIES CODE INFORMATION
SERIES CODE C MAX DIM A 1.156 B 1.156 C 1.000 D 1.214 E 1.214 F 1.156 FM 1.156 G 1.237 H 1.654 J .809 K .904 KA .759 KB .799 KC .745 KD .904 L .873 M .966 N 1.000 P 1.154 R 1.123 T 1.154 U 1.232 W 1.039 X .994     ENTRY SIZE D MAX DIA E MAX DIA F MAX DIA G MAX DIM H MAX DIM CABLE ENTRY MAX MIN 02 N / A .840 .781 N / A N / A .250 .125 03 .858 .965 .906 1.36 1.86 .375 .156 04 .858 1.090 1.031 1.49 1.98 .500 .281 05 1.112 1.215 1.156 1.61 2.11 .625 .406 06 1.218 1.340 1.281 1.74 2.23 .750 .531 07 1.345 1.465 1.406 1.86 2.36 .875 .656 08 1.468 1.590 1.531 2.11 2.61 1.000 .781 09 1.593 1.715 1.656 2.11 2.61 1.125 .906 10 1.969 1.840 1.781 2.34 2.73 1.250 1.031 11 1.969 1.965 1.906 2.36 2.86 1.375 1.156 12 2.219 2.090 2.031 2.61 3.11 1.500 1.281 ORDER NUMBER J MAX DIM K MAX DIM 01 - 06, 08, 52, 54, 64, 65 1.82 1.98 07, 09 - 12, 14, 53, 55 - 58, 67, 69, 70 2.08 2.23 13, 15, 16, 18 - 24, 59 - 61, 71, 72, 74 2.45 2.61 25 - 29, 49, 50, 62, 77 2.70 2.86 30 - 40, 63 3.45 3.61 41 - 48 3.82 3.98 NOTES: Identified Per MIL-STD-130 Plating Index for Finishes Available Material; Adapter Components; Aluminum Alloy Per QQ-A-225 or QQ-A-591. Spring Screws and washers, stainless steel. Elastomers, Standard Neoprene Per MIL-R-3065 or Silicone (See Note 4) Per ZZ-R-765. Insert the following letter(s) for the function required: 'R' - Elbow with RFI Rings. 'E' - Environmental (Neoprene Elastomers, Non-RFI). 'S' - Environmental (Silicone Elastomers, Non-RFI). 'RE' - RFI & Environmental (Neoprene Elastomers) 'RS' - RFI & Environmental (Silicone Elastomers) Insert letter 'C' for 'C' nut (no strian relief) (omit letter for strain relief clamp) Two-Piece assembly supplied when cable entry exceeds connector insert Dia. D, G, and H dimensions apply to two- piece assemblies only SE97-***-* ground support ring (ordered sperately is recommended for all rfi assemblies and when shield support ring must be used for sufficient grounding. (see SE97) DIMENSIONS ARE IN INCHES Tolerance, unless otherwise specified: .X ± .03 (1.5) .XX ± .010 (0.8) .XXX ± .005 (0.4) Angles: ± 5 degrees Fractions ± 1/32 Click here for this part's assembly procedure (AP27)