Overall Shield Termination
click here for Individual and Overall Shield Termination
CLICK HERE TO VIEW A LARGER IMAGE
STEP 1: TEMPORARILY ASSEMBLY SLEEVE TO CONNECTOR
CLICK HERE TO VIEW A LARGER IMAGE
STEP 2: SLIDE NUT UP CABLE AWAY FROM TERMINATION AREA SO AS NOT TO INTERFERE WITH SUBSEQUENT ASSEMBLY STEPS
CLICK HERE TO VIEW A LARGER IMAGE
STEP 3: INSERT CABLE INTO SLEEVE AND BOTTOM AGAINST CONNECTOR HOLD CABLE IN POSITION AND MARK JACKET AT END OF SLEEVE
CLICK HERE TO VIEW A LARGER IMAGE
SETP 4: DISASSEMBLE SLEEVE FROM CONNECTOR AND SLIDE SLEEVE UP THE CABLE WITH NUT. (SLIDE WIRE RING UP CABLE AFTER SLEEVE IF APPLICABLE)
CLICK HERE TO VIEW A LARGER IMAGE
STEP 5: TRIM CABLE JACKET 1/2 INCH PLUS LENGTH OF WIRE THAT WILL PROTRUDE INSIDE OF CONNECTOR, BEHIND MARK (REF STEP 3) BEING CAREFUL NOT TO CUT OVERALL SHIELD
CLICK HERE TO VIEW A LARGER IMAGE
STEP 6: PREPARE OVERALL SHIELD BY FLARING OUT AND SECURING AGAINST OUTER PERIPHERY OF CABLE AND SPOT TIE (TERMPORARILY).
STEP 7: TERMINATE CONDUCTORS IN ACCORDANCE WITH NORMAL PRACTICES
STEP 8: ASSEMBLE SLEEVE TO CONNECTOR AND TIGHTEN
CLICK HERE TO VIEW A LARGER IMAGE
STEP 9: FLARE SHIELD OVER REAR OF SLEEVE SLIDE DOWN NUT AND THREAD ONTO SLEEVE SECURLY AND TORQUE TO 75 INCH POUNDS AND TRIM ANY EXPOSED SHIELD STRANDS AT FOWARD END OF NUT
STEP 10: SHRINK BOOT MAY BE INSTALLED AT THIS TIME
Individual and Overall Shield Termination
click here for Overall Shield Termination
CLICK HERE TO VIEW A LARGER IMAGE
STEP 1: TEMPORARILY ASSEMBLE SLEEVES (1) AND (2) TOGETHER AND ASSEMBLE SLEEVES TO CONNECTOR
CLICK HERE TO VIEW A LARGER IMAGE
STEP 2: SLIDE NUT UP CABLE AWAY FROM TERMINATION AREA SO AS NOT TO INTERFERE WITH SUBSEQUENT ASSEMBLE STEPS.
CLICK HERE TO VIEW A LARGER IMAGE
STEP 3: INSERT CABLE INTO SLEEVES AND BOTTOM AGAINST CONNECTOR. HOLD CABLE IN POSITION AND MARK JACKET AT END OF SLEEVE (2)
CLICK HERE TO VIEW A LARGER IMAGE
STEP 4: REMOVE CABLE FROM SLEEVES REMOVE SLEEVE(2) FROM SLEEVE(1) AND SLIDE SLEEVE (2) AND GROUND RING UP CABLE WITH NUT
CLICK HERE TO VIEW A LARGER IMAGE
STEP 5: TRIM CABLE JACKET 1/2 INCH PLUS LENGHT OF WIRE THAT WILL PROTRUDE INSIDE OF CONNECTOR BEHIND MARK BEING CAREFUL NOT TO CUT OVERALL SHIELD
STEP 6: INSERT CABLE IN TO SLEEVE(1) AND BOTTOM AGAINST CONNECTOR, HOLDING CALBE IN PLACE MARK OVERALL SHIELD AT END OF SLEEVE.
CLICK HERE TO VIEW A LARGER IMAGE
STEP 7: DISCONNECT SLEEVE(1) FROM CONNECTOR AND SLIDE SLEEVE UP CABLE WITH OTHER COMPONENTS (SLIDE WIRE SEAL RING UP CABLE AFTER SLEEVE IS APPLICABLE)
CLICK HERE TO VIEW A LARGER IMAGE
SETP 8: TRIM OVERALL SHIELD 1/2 INCH FROM MARK TOWARDS END OF CABLE BEING CAREFUL NOT TO CUT INDIVIDUAL SHIELS, FOLD BACK AND SPOT TIE.
CLICK HERE TO VIEW A LARGER IMAGE
STEP 9: EXTRACT WIRES FROM INDIVIDUAL SHIELDS 1 INCH BACK FROM CABLE JACKET (REF AP95) FOLD BACK INDIVIDUAL SHIELDS AND SPOT TIE
STEP 10: TERMINATE CONDUCTORS IN ACCORDANCE WITH NORMAL PRACTICES
STEP 11: SLIDE DOWN SLEEVE(1) AND ASSEMBLY TO CONNECTOR AND TIGHTEN
CLICK HERE TO VIEW A LARGER IMAGE
STEP 12: UNTIE INDIVIDUAL SHIELDS SLIDE GROUND RING DOWN FLARE SHIELDING OUT, OVERA ND AROUND GROUND RING
STEP 13. SLIDE GROUND RING TINO PLACE IN TAPERED BORE AT REAR OF SLEEVE(1) TRIM EXCESS SHIELD AND SPOT TIE IF NECESSARY
CLICK HERE TO VIEW A LARGER IMAGE
STEP 14: SLID SLEEVE(2) AND THREAD ONTO SLEEVE 1 AND TIGHTEN
CLICK HERE TO VIEW A LARGER IMAGE
STEP 15: FLARE OVERALL SHIELD OVER REAR OF SLEEVE(2) SLIDE DOWN NUT AND THREAD ONTO SLEEVE SECURELY AND TORQUE TO 75 INCH POUNDS TRIM ANY EXPOSED SHIELD STRANDS AT FORWARD END OF NUT
STEP 16: SHRINK BOOT MAY BE INSTALLED AT THIS TIME
